Auto Start Control Module (Electronic engine enabled)

The DSE5510 is an Automatic Engine Control Module, designed to provide advanced load share functionality for diesel and gas generating sets that include non-electronic and electronic engines. The module also provides excellent engine monitoring and protection features.    The modules load share functions include, automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s). The module has been designed to combine a maximum of 16 generators and 16 mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4 mains (utility) supplies (DSE5560 required to synchronise with the mains)   The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

Auto Mains Failure & Instrumentation Control Module (Electronic engine enabled)

The DSE5520 is an Automatic Mains Failure Control Module designed to provide advanced load share functionality for diesel and gas generating sets that include non electronic and electronic engines. The module also provides excellent engine monitoring and protection features.    The module monitors the mains (utility) supply and upon detection of a loss in power automatically starts the generating set.   The modules synchronising functions include automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s).  The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

Auto Transfer Switch & Mains Control Module

The DSE5560 is an Automatic Transfer Switch and Mains Control Module, designed to automatically synchronise multiple DSE5510’s with single or multiple mains (utility) supplies. The module instructs the DSE5510’s to make precise changes to the generating set outputs. This makes the module suitable for many applications including peak lopping, peak shaving and no break return.   The module has the ability to monitor the mains (utility) supply and start and stop the generating sets (being controlled by a DSE5510) upon removal or detection of the mains (utility) supply. The modules operational status is indicated on the LCD display and the front panel LED’s.

Auto Start Control Module (Electronic Engine Enabled)

The DSE7510 is an Automatic Engine ControlModule, designed to provide advanced load share functionality for diesel and gas generating sets that include nonelectronic and electronic engines.  The module also provides excellent engine monitoring and protection features. 

The module’s load share functions include, automatic synchronizing with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVRs). 

The module has been designed to combine a maximum of 16 generators and 16mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4mains (utility) supplies (DSE7560 required to synchronise with the mains).  The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync,MPU open circuit failure, negative phase sequence and loss of excitation.

Auto Mains (Utility) Failure & Instrumentation Control Module (Electronic Engine Enabled)

The DSE7520 is an Automatic Mains Failure Control Module designed to provide advanced load share functionality for diesel and gas generating sets that include non electronic and electronic engines, for single set appications and parallel with mains. The module also provides excellent engine monitoring andprotection features.  

The module monitors the mains (utility) supply and, upon detection of a loss of power, automatically starts the generating set. 

The module’s synchronizing functions include automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVRs). 

 The module has the ability to monitor generator under/over generator volts, over current, under/over generator

frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync,MPU open circuit failure, negative phase sequence and loss of excitation.

Auto Transfer Switch & Mains (Utility) Control Module

The DSE7560 is an Automatic Transfer Switch and Mains Control Module, designed to automatically synchronise multiple DSE7510s with single or multiple mains (utility) supplies.  The module instructs the DSE7510s to make precise changes to the generating set outputs. This makes the module suitable for many applications including peak lopping, peak shaving and no break return. 

The module has the ability to monitor the mains (utility) supply and start and stop the generating sets (being controlled by a DSE7510) upon removal or detection of the mains (utility) supply. The modules operational status is indicated on the LCD display and the front panel LEDs.

Auto Start Multi-Set Controller

The DSE8610 is an easy to use multi-generator loadshare system, designed to synchronise  up to 32 generators including electronic and non-electronic engines.

The DSE8610 monitors the engine and indicates operational status and fault conditions, automatically starting or

stopping the engine on load demand or fault condition.

Failures are annunciated on the LCD screen (multiple language options available), illuminated LED and audible sounder.

The event log will record 250 events to facilitate easy maintenance. An extensive number of fixed and flexible monitoring, metering and protection features are included as well as sophisticated communication and system expansion options.

Using the DSE PC Configuration Suite Software allows easy alteration of the operational sequences, timers and alarms.

With all communication ports able to be active at the same time, the DSE8610 is ideal for a wide variety of demanding load share applications.

Auto Transfer Switch and Mains Control Module

The DSE8660 is an easy-to-use single or multi-mains controller with automatic transfer switch capability.  Designed to synchronise single or multiple DSE8610s with single or multiple mains(utility) supplies, the DSE8660 will automatically control the change over from mains (utility) to generators in synchronisation with the mains (utility) to provide no-break, peak lopping and peak shaving power solutions.

The module can indicate operational status and fault conditions on the LCD screen (multiple languages available), by lit LED, audible sounder and SMS messaging.  Sophisticated communications are also available via RS485 and RS232 for remote PC control and monitoring and intigration into building management systems.  The comprehensive event log will record up to 250 events to facilitate easy maintenance.

An extensive number of fixed and flexible monitoring and protection features are included.  Easy alteration of the timers, sequences and alarms can be made using the DSE PC Configuration Suite Software.  Selected programming is also available via the module's front panel making the DSE8660 ideal for a wide variety of load share applications.