GE
Administrator
A3200040,
LV HRC switch-disconnector-fuse in acc. With DIN EN 60937-3 for LV HRC fuse-links in acc. With DIN43620
without accessories
L5651001, L00-3/100
LV HRC strip type fuse way acc. to EN 60269-2 for fuse-links acc to DIN 43636
Universal flat terminal M8; clamp-type terminal or v-terminalclamp retrofitable
L5651001, L00-3/100
LV HRC strip type fuse way acc. to EN 60269-2 for fuse-links acc to DIN 43636
Universal flat terminal M8; clamp-type terminal or v-terminalclamp retrofitable
ERICO offers the SB range of power blocks and SBLL, SBLT and SBTT range of power terminals, part of the ERIFLEX® line of low-voltage power distribution products. These easy-to-use products provide a high-quality, reliable connection between two electrical circuits, such as cables and/or ERIFLEX® FLEXIBAR in the panel. Power terminals and power blocks are found at the power entry and exit of nearly all equipment.
Ranging from 125A to 1250A IEC® and 150A to 760A UL®, power blocks and power terminals offer an easy connection on ERIFLEX FLEXIBAR plain or tinned copper and/or copper or aluminum cables.
ERICO's ISO 9001 certified quality control procedures and proprietary automated manufacturing processes have made ERIFLEX® FLEXIBAR the preferred conductor for panelboard designers and assemblers throughout Europe and the Americas. ERIFLEX FLEXIBAR has many years of proven low voltage application success throughout the world.
ERICO's ISO 9001 certified quality control procedures and proprietary automated manufacturing processes have made ERIFLEX® FLEXIBAR the preferred conductor for panelboard designers and assemblers throughout Europe and the Americas. ERIFLEX FLEXIBAR has many years of proven low voltage application success throughout the world.
The DSE5510M is an Automatic Engine Control Module, designed to provide advanced load share functionality for diesel and gas generating sets that include non-electronic and electronic engines. The module also provides excellent engine monitoring and protection features. The modules load share functions include, automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s). The module has been designed to combine a maximum of 16 generators and 16 mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4 mains (utility) supplies (DSE5560 required to synchronise with the mains) The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.
The DSE332 is an Automatic Transfer Switch Controller for single set genset applications. The module will monitor the voltage and frequency of the incoming AC mains (utility) supply (supports many topologies) and in the event of a failure will issue a start command to the generator control system.
Once the generator is available and producing an output within limits, the DSE332 will control the transfer devices and switch the load from the mains (utility) to the generating set. Once the mains (utility) supply returns to within limits, the module will command a return to the mains (utility) supply and shut down the generator after a cooling run. Various timing sequences are available to prevent nuisance starting on minor supply breaks.
The DSE332 includes a clear back-lit LCD 4-line text display, showing system status and warnings. Red and Green LEDs also indicate operation status. The module includes configurable digital inputs and outputs and is programmable by PC using the user-friendly DSE Configuration Suite Software. Limited programming is also available via the module’s front panel.
The DSE2510 is remote device designed to work with the DSE7310 Auto Start and control module.
Up to three remote devices can be connected to one host control module up to 1km away. The devices offer exactly the same instrumentation, control and monitoring capabilities as the host control module, including starting and stopping of the engine.
All three remote devices will display the same information at the same time, while the host controller is able to work independently, showing different sets of information.
The modules are simple to operate and feature the same user-friendly menu layout as the host module.
All communications and programming are done via the host module only. The remote devices simply mirror the programming of the host module making the system quick and easy to install.
The EC machinery directive 2006/42/EC demands that there is no danger posed by machines.
The monitoring of safety-oriented components such as Emergency-Stop circuits, safety doors, light curtains, two-hand controls, etc. is an important criteria for fulfilment of this requirement.
The new ESR5 safety relays provide optimum safety and the highest levels of reliability on machines and systems.